Firewalls and Security Software¶
The perfSONAR Toolkit utilizes a number of tools the help protect against attacks on the system. Some of these tools include:
A default set of host firewall rules that only allow connections to ports required by perfSONAR tools.
Inclusion of the fail2ban intrusion detection system (IDS) to log suspicious activity such as brute-force SSH attacks
None of these solutions will protect your host from all kinds of attacks so best common practices and good sense should be used when administering your host. In addition to tools like above it’s important update your host with the latest packages and to watch the mailing lists for important security announcements.
Default Firewall Rules and perfSONAR port requirements¶
The perfSONAR Toolkit uses iptables and ip6tables to implement IPv4 and IPv6 firewall rules respectively. The default configurations for iptabel are in /etc/sysconfig/iptables and /etc/sysconfig/ip6tables. Also see /usr/lib/firewalld/services and /etc/perfsonar/toolkit/perfsonar_firewalld_settings.conf for firewalld settings depending on operating system.
The current perfSONAR release uses the following ports (used by a Tool when requesting a test. See also Test and Tool Reference) by default:
perfSONAR Tools Ports |
||
|---|---|---|
Tool |
TCP ports |
UDP Ports |
owamp (control) |
861 |
|
owamp (test) |
8760-9960 |
|
twamp (control) |
862 |
|
twamp (test) |
18760-19960 |
|
pscheduler |
443 |
|
traceroute |
33434-33634 |
|
simplestream |
5890-5900 |
|
nuttcp |
5000, 5101 |
|
iperf3 |
5201 |
|
iperf2 |
5001 |
|
ntp |
123 |
|
Some ports are also used to access the perfSONAR Toolkit management interfaces:
perfSONAR Toolkit Ports |
|
|---|---|
Tool |
TCP ports |
management interface |
443 |
archive (opensearch, logstash) |
443 |
Note
ICMP also needs to be open
Lookup Service Registration Requirements¶
For the Lookup Service registration to work make sure your host enables outgoing traffic to the following hosts:
Port TCP/80 access to 198.128.151.2 to access the Lookup Service bootstrap host
Port TCP/8090 access to 35.223.142.206 to register the host to the Lookup Service
Adding Your Own Firewall Rules¶
For operating systems using iptables, the rules added by the perfSONAR Toolkit are contained within a special perfSONAR chain of iptables (and ip6tables). You may add rules to the other chains, such as the INPUT chain, just as you would any other firewall rule. It is NOT recommended you change the perfSONAR chain as any changes you make could be overwritten by a software update.
For operating systems using firewalld it organizes the rules into “zones” and makes it more difficult to distinguish perfSONAR rules from custom rules. If you add a standard service to the zone it will get overwritten next time perfsonar-toolkit-security upgrades. We recommend looking at firewalld rich rules for adding custom rules.
For more information see:
Fail2ban Intrusion Detection System¶
By default the perfSONAR Toolkit installs and configures the fail2ban Intrusion Detection System (IDS). This software will log suspicious activity such as a rapid succession of failed SSH login attempts in /var/log/secure. By default it will not act to mitigate any attempts, only log them (though the default IP table rules do SSH throttling). If you would like to change this default behavior to send email or block unwanted intrusions, see the configuration file /etc/fail2ban/jail.conf and the fail2ban manual for details.
Limiting tests to Research and Education Networks Only¶
ESnet provides a file containing all R&E subnets, which is updated nightly. Instructions on how to download this file and configure pScheduler to use it are described on the page Limiting Tests to R&E Networks Only.
Managing Login Access¶
perfSONAR nodes are meant to be used, both by local users and the public at large, to perform a variety of network tests. The open access policy is at odds with ways to mitigate the risk of exposing functionality to those that would cause harm. The following is a possible approach for managing access to the host:
SSHD can be turned off completely if remote access to the machine via the terminal is not need (e.g. in cases where console access is available either directly, or indirectly)
If SSHD is turned on, consider using a jump host setup wherein access to the perfSONAR node can only be accomplished through a single (or set) of trusted hosts. This type of restriction can be implemented in IPTables.